Module guide · Available

Thermodynamic Processes: from one state to another

Given an initial state and a constraint on the process, where does a fluid end up, and what heat and work accompany the change? This module reads states on property diagrams, applies one process constraint at a time, and then uses those ideas in steady-flow devices such as nozzles, turbines, compressors, pumps and throttles.

Part of Chemical Engineering Thermodynamics. Builds on Pure Component Properties.

The question this module answers

Steam expands through a turbine, refrigerant drops in pressure across a valve, air is compressed before a combustor, a sealed vessel is heated. Each is a change from one equilibrium state to another under a constraint: constant temperature, constant pressure, no heat transfer, constant enthalpy. Knowing the constraint and the initial state is enough to find the final state and the energy exchanged.

Thermodynamic Processes teaches these individual paths and the steady-flow devices that use them. Complete cycles, in which several processes are joined, are the subject of the upcoming Thermodynamic Cycles module.

Before you start

Internal energy, enthalpy, entropy, saturation and quality from Pure Component Properties, and the first and second laws for closed systems.

State versus path

Internal energy, enthalpy and entropy are state functions: their changes depend only on the end states. Heat and work are not; they depend on the path between them. That is why a process must be specified by its constraint, not only by its end points.

ChETL follows the sign convention of Smith, Van Ness and Abbott: heat and work are positive when they enter the system. For a closed system with negligible changes in kinetic and potential energy,

ΔU = Q + W   ΔS = ∫dQ/T + SG,  SG ≥ 0

Here W is all the work done on the system, and T in the entropy balance is the temperature where heat crosses the boundary. For mechanically reversible boundary work alone, W = −∫P dV, which is negative for an expansion.

Entropy generation SG is zero only for a reversible process. It measures how far a real process falls short of the ideal, and it is the second-law test of whether a proposed process is possible.

How the eight topics connect

Pure Component Propertiesstate properties and saturation
Property diagramsstate, phase and diagram literacy
Constant-property paths
IsothermalIsobaricIsochoric
Adiabatic and isentropicenergy, entropy and reversibility
IsenthalpicthrottlingPolytropica family of paths
Flow processesnozzle, diffuser, turbine, compressor, blower, fan, pump, throttle
Thermodynamic Cyclesupcoming module · not yet available
A learning map. Topics on the same row are siblings, each applying its own constraint; no arrow joins them. Downward arrows show the learning progression, not strict mathematical dependency: Flow Processes applies the ideas of every earlier stage. Dashed boxes are context outside this module.

Suggested study order: a learning progression, not a scientific dependency

  1. Property diagrams
  2. Constant-property paths
  3. Adiabatic and isentropic
  4. Isenthalpic and polytropic
  5. Flow processes

Learn to read states on diagrams, apply one constraint at a time to a closed system, add the reversible adiabatic limit and entropy generation, generalise to throttling and polytropic paths, then use them all in steady-flow devices.

Property diagrams

How do I read a thermodynamic path and phase region?

The Property Diagrams topic places a single state, defined by temperature and pressure or by one of them and the vapour quality, on five diagrams. Each is useful for a different job:

PV
for a mechanically reversible closed-system path, the area under the curve is the magnitude of the boundary work; the work done on the system is W = −∫P dV.
TS
the area under an internally reversible path is the heat transferred; isentropic steps are vertical lines.
PH
throttling is a vertical line at constant enthalpy and constant-pressure heating is horizontal; the usual chart for refrigeration.
HS (Mollier)
enthalpy drops across turbines and nozzles read directly, with isentropic expansion as a vertical line.
PT
the vapour-pressure curve ending at the critical point separates liquid from vapour.

All except PT show the saturation dome, the critical point and the two-phase region, where quality sets the proportion of vapour. Geometry has thermodynamic meaning only under stated conditions: an area under a PV path measures boundary work only if the path is mechanically reversible, and it says nothing about shaft or other work.

Constant-property paths

What happens when temperature, pressure or volume is held constant?

Isothermal
For an ideal gas ΔU = 0, so Q = −W; the mechanically reversible work done on the gas per mole is W = RT ln(P2/P1), positive for compression. A real fluid’s internal energy does change with pressure at constant temperature. Physically, a subcritical isothermal path can cross liquid–vapour coexistence at constant vapour pressure, but the current Isothermal topic calculates single-phase paths only and reports a phase-crossing request as unavailable.
Isobaric
For a closed system at constant pressure whose only work is mechanically reversible boundary work, W = −PΔV and therefore Q = ΔH. This covers sensible heating and cooling and phase change at constant pressure, where temperature stays at saturation while quality changes.
Isochoric
In a rigid closed vessel with no stirring, shaft or electrical work, W = 0, so Q = ΔU. Heating raises the pressure; whether a wet mixture ends as liquid or vapour depends on whether its volume is below or above the critical volume.

Each process topic also works the ideal-gas reference from the textbook relations, so the real-fluid result can be compared with it and the effect of non-ideality seen.

Adiabatic is not the same as isentropic

What changes when heat transfer is zero, and when is the process isentropic?

An adiabatic (insulated) closed system exchanges no heat, so ΔU = W and ΔS = SG ≥ 0. Only a reversible adiabatic process is isentropic. The topic’s irreversible cases are insulated ones: expansion against a constant external pressure, and free expansion into an evacuated space, each inside adiabatic walls. Neither expansion is adiabatic by nature; with heat exchange allowed they would be different processes. Insulated, they generate entropy, and the topic compares them with the isentropic path from the same initial state as a benchmark.

The familiar ideal-gas relation PVγ = constant needs an ideal gas, constant heat capacities and a reversible path. Real-fluid isentropic paths are found from the entropy itself, including expansions that end inside the two-phase region.

Throttling: the isenthalpic process

What happens across a throttling valve?

For steady flow through a valve with no heat transfer, no shaft work and negligible changes in kinetic and potential energy, the outlet enthalpy equals the inlet enthalpy: H2 = H1. An ideal gas leaves at the same temperature. A real fluid usually cools, sometimes heats, according to its Joule–Thomson coefficient μJT = (∂T/∂P)H, and a saturated or compressed liquid may partly flash to vapour.

Throttling is irreversible, so S2 > S1. The states inside the valve are not equilibrium states, so only the inlet and outlet are calculated; no path through the device is drawn.

Polytropic paths

How does PVδ = constant describe a family of compression and expansion paths?

A single exponent δ describes a mechanically reversible closed-system path, PVδ = constant. For an ideal gas, special values recover familiar processes: δ = 0 is isobaric, δ = 1 isothermal, δ = γ isentropic (with constant heat capacities) and δ → ∞ isochoric. Boundary work follows from the path, and heat from Q = ΔU − W. For a real fluid the same imposed path is followed with real-fluid properties, with breaks shown where the path cannot be resolved.

Steady-flow devices

How do nozzles, turbines, compressors and pumps convert stream energy?

For one stream in steady flow, per unit mass,

ΔH + Δu2/2 + gΔz = Q + Ws

Nozzles and diffusers trade enthalpy for velocity. Turbines and expanders deliver shaft work; compressors, blowers, fans and pumps consume it. Real devices are compared with an isentropic device between the same inlet state and outlet pressure:

ηturbine = ΔH/(ΔH)S   ηcompressor = (ΔH)S/ΔH

The current scope is adiabatic, single-stream devices handling a pure fluid. Polytropic efficiency, nozzle geometry and choking, heated or cooled devices and multistage machines are not included.

Fluid models and reference states

Real-fluid properties come from the Peng–Robinson, Soave–Redlich–Kwong or Redlich–Kwong equation of state with Antoine saturation pressures, for any supported pure fluid. For water, IAPWS-IF97 is offered first, with the cubic equations kept for comparison.

IAPWS-IF97 uses the steam-table reference (internal energy and entropy zero for saturated liquid at the triple point), not the formation-based reference of the other models. Changes such as ΔH are valid within either; absolute values from the two are never mixed, and the ideal-gas overlay is withheld on diagrams with an absolute energy or entropy axis for that reason.

Common misunderstandings

  • “Adiabatic means isentropic.” Only a reversible adiabatic process is isentropic.
  • “Adiabatic means the temperature stays constant.” No heat crosses the boundary, but work changes the internal energy, and usually the temperature.
  • “Q = ΔH for any heating.” Only for a closed system at constant pressure whose only work is mechanically reversible boundary work, or for a steady-flow process with no shaft work and negligible kinetic and potential changes.
  • “A throttle is a turbine without the work.” Its outlet enthalpy equals its inlet enthalpy; the lost opportunity to do work appears as entropy generation.
  • “Isentropic efficiency compares with the outlet temperature.” It compares enthalpy changes with an isentropic device that reaches the same outlet pressure.

Scope and limits

  • Pure fluids and single paths or devices. Mixtures are not used as working fluids here.
  • Isothermal paths stay in one phase. Isothermal paths that would cross liquid–vapour coexistence, or end inside it, are reported as unavailable for now. Isobaric and isochoric paths do follow phase change.
  • No complete cycles. Power, refrigeration, heat-pump and liquefaction cycles are the subject of the upcoming Thermodynamic Cycles module, which is not yet available.
  • No equipment design. Mechanical design, detailed fluid mechanics, valve or nozzle sizing and economics are outside the module.
  • Exergy analysis is not currently included.
  • Model results. States outside a model’s range, or ones it cannot represent, are reported as unavailable; results are for learning, not for design.

Sources and next steps

  • J. M. Smith, H. C. Van Ness, M. M. Abbott and M. T. Swihart, Introduction to Chemical Engineering Thermodynamics, 9th ed.: chapter 3 (ideal-gas process paths), chapter 5 (entropy and isentropic relations), chapter 6 (thermodynamic diagrams) and chapter 7 (applications to flow processes).
  • International Association for the Properties of Water and Steam, Revised Release on the IAPWS Industrial Formulation 1997 for the Thermodynamic Properties of Water and Steam (IAPWS-IF97).
  • This guide summarises ChETL’s documented module scope as of 9 November 2026; editorial responsibility rests with the ChETL Scientific Editor. See sources, review and limits; report errors through Contact.

Launch ChETL

Launch ChETL