Course guide

Chemical Engineering Thermodynamics: the course map

Chemical engineering thermodynamics is the first course on ChETL. Five of its modules are available today and a sixth, Thermodynamic Cycles, is upcoming. This page explains what each module answers, how the modules depend on one another, what to know before you begin and where the current scope stops.

What the course is for

Almost every chemical engineering decision rests on a thermodynamic question asked first. How much space does a gas occupy at the pressure in this vessel? Which components go to the vapour when this mixture boils? How far can this reaction proceed before it stops? How much work does this compressor need, and how much heat must be removed? The answers set the limits that rate processes, equipment and economics then work within.

The course follows the undergraduate sequence of the standard chemical engineering thermodynamics texts, principally Smith, Van Ness, Abbott and Swihart. It starts with the properties of a single fluid, extends them to mixtures, applies them to phase and reaction equilibrium, and uses them to analyse processes that move a fluid from one state to another. Throughout, the emphasis is on understanding which model is being used, why, and when its answer should not be trusted.

This page is a guide to the course and its capabilities. Complete worked calculations are published separately as worked examples; two are available so far, the ethanol–water P–xy example and the NRTL activity-coefficient example.

How the modules connect

Each module builds on quantities that an earlier module defines, rather than deriving them again. Pure Component Properties is the foundation: it supplies the volumetric, energy, fugacity and saturation properties of single substances. The map shows where each module draws its ideas from.

Pure Component Propertiesone substance at a stated state
Solution Thermodynamicscomponents inside mixtures
Phase Equilibriumcoexisting vapour and liquid Chemical Equilibriumreacting mixtures
Thermodynamic Processespaths, heat, work and flow devices Thermodynamic Cyclesupcoming · not yet available
Course map. An arrow means “builds on ideas defined in”: Solution Thermodynamics and Thermodynamic Processes both draw on Pure Component Properties; Phase Equilibrium and Chemical Equilibrium sit downstream of the mixture concepts. Chemical Equilibrium’s current gas-phase scope mainly uses pure-component thermochemical data. Thermodynamic Cycles, drawn dashed, is upcoming. The map shows scientific relationships; the suggested study order is given separately below.

Which module answers your question?

If you arrive with a specific problem rather than a syllabus, start from the question.

Questions and the modules that answer them
Your questionModule
How far does a real gas or liquid depart from ideal-gas behaviour at a given temperature and pressure?Pure Component Properties
What are a pure fluid’s enthalpy, entropy, fugacity or vapour pressure at a state?Pure Component Properties
How does a component behave inside a mixture, and how far is the solution from ideal?Solution Thermodynamics
At what pressure or temperature does a mixture begin to boil or condense, and how much vapour forms at a given temperature and pressure?Phase Equilibrium
How far does a gas-phase reaction go, and how do temperature, pressure and feed shift it?Chemical Equilibrium
What heat and work accompany heating, compression, expansion or throttling of a fluid?Thermodynamic Processes
How does a complete power or refrigeration cycle perform?Thermodynamic Cycles (upcoming)

A suggested order of study

The platform lists the modules in the order below. It is a learning progression, not a rule: the map above shows which modules genuinely depend on which.

Suggested study order: a learning progression, not a scientific dependency

  1. Pure Component Properties
  2. Solution Thermodynamics
  3. Phase Equilibrium
  4. Chemical Equilibrium
  5. Thermodynamic Processes

Phase Equilibrium needs both earlier modules. Thermodynamic Processes needs only Pure Component Properties, so a course centred on energy analysis can move to it directly. Chemical Equilibrium can follow Pure Component Properties in its current gas-phase scope, although activities and fugacities read more naturally after Solution Thermodynamics.

Within each module the topics also have a suggested order, explained in the module guides. In Phase Equilibrium, for example, P–xy, T–xy and flash are sibling problems that share one foundation; in Pure Component Properties most later topics build on quantities defined earlier, such as residual properties on the ideal-gas reference and fugacity on residual Gibbs energy, although the topic order itself is a teaching sequence.

What to know before you start

ChETL begins with the properties of fluids, not with the laws of thermodynamics themselves. You will get more from it if you already have:

  • introductory thermodynamics: system and surroundings, state and path, the first law as an energy balance, and the idea of entropy and the second law;
  • mathematics: algebra, logarithms and exponentials, derivatives and integrals, and reading graphs with logarithmic axes;
  • units: converting between pressure, temperature and energy units (bar, kPa, K, °C, J/mol) and keeping molar and mass bases apart;
  • stoichiometry and material balances: mole fractions, conversion and simple balances, especially for the equilibrium modules.

No programming is needed. Calculations are set up by choosing components, models and conditions in a configuration panel; the platform’s engine does the computation and shows its steps.

How each topic is taught

Every module is divided into topics, and every topic opens in the same workspace. The tabs answer different questions about one calculation:

Theory
a written chapter on why the topic matters and how the general method works, with a solution-strategy flowchart; no numbers.
Blackboard
the engine’s worked arithmetic for the configured case: knowns and their sources, assumptions, then formula, substitution and result, with units.
Plot and Data
the same calculation across a range of conditions, with the configured state marked, and the underlying table.
Interpretation
what this result means, how it compares with a reference, and the model’s validity and limitations.
AI Tutor
questions about the case you have open, answered in its context; it cannot change the calculated values.
Assessment
short question sets at three levels, with immediate or end-of-session feedback.

The screenshot tour follows one case through every tab, and the philosophy explains why the surfaces are separated this way.

Scope and limits of the course

The course covers the undergraduate core of the subject. Each module guide states its own boundaries; across the course, these limits apply:

  • Phase equilibrium is vapour–liquid only. Liquid–liquid, vapour–liquid–liquid and solid–liquid equilibria and general phase-stability analysis are not offered.
  • Reaction equilibrium covers homogeneous gas-phase reactions treated as ideal-gas mixtures. Liquid-phase, electrolyte and combined reaction-and-phase equilibria are not offered, and reaction rates and reactor sizing belong to reaction engineering, not thermodynamics.
  • Process analysis covers single paths and single devices for pure fluids. Complete cycles are the subject of the upcoming Thermodynamic Cycles module; mechanical design and equipment sizing are outside the course.
  • Results are model estimates for learning. A result is as good as its model, its parameters and their stated ranges. ChETL results are not design values, and broad validation against experimental data is not claimed.
  • Missing data are reported, not filled. When a model lacks parameters for a component, or a condition falls outside what a route can represent, the platform reports the calculation as unavailable instead of substituting another model.

Module availability is summarised on Development status, and the project’s approach to sources, review and limits on About.

Module guides

Each guide explains the module’s scientific question, how its topics connect, the models and data choices it involves, common misunderstandings and its limits.

Available

Pure Component Properties

Nine topics from compressibility and molar volume through residual properties, enthalpy, entropy, Gibbs energy and fugacity to saturation.

Available

Solution Thermodynamics

Partial molar, mixing and excess properties, activity coefficients and equation-of-state mixture fugacity.

Available

Phase Equilibrium

Bubble and dew calculations, P–xy and T–xy diagrams with their x–y view, and TP flash.

Available

Chemical Equilibrium

Equilibrium constants and their temperature dependence, and single and multiple independent gas-phase reactions.

Available

Thermodynamic Processes

Property diagrams, constant-property, adiabatic, isenthalpic and polytropic paths, and steady-flow devices.

Upcoming

Thermodynamic Cycles

Power, refrigeration and related cycles assembled from the process paths. Not yet available; no guide is published until it is.

Sources and next steps

  • Principal reference: J. M. Smith, H. C. Van Ness, M. M. Abbott and M. T. Swihart, Introduction to Chemical Engineering Thermodynamics, 9th ed. Notation on the platform follows this text, with differences stated where they occur.
  • Scope: this guide summarises ChETL’s documented module scope as of 9 November 2026, under the editorial responsibility of the ChETL Scientific Editor (project owner).
  • Corrections: email info@chetl.org with the page and what looks wrong; see Contact.

Launch ChETL

Launch ChETL