Module guide · Available

Pure Component Properties: a guide to the module

Take one substance at a stated temperature and pressure. How much space does it occupy, how much energy does it carry, how far is it from an ideal gas, and when does it boil? This module answers those questions for a single fluid and supplies the pure-component quantities that every later thermodynamics module uses.

Shown as Pure Properties in the platform. Part of Chemical Engineering Thermodynamics.

The question this module answers

A storage sphere of butane, a steam line and a refrigerant charge all start from the same problem: given a substance and its state, what are its properties? The ideal-gas law answers part of it at low pressure. Nearer saturation, at high pressure or in the liquid, molecules occupy space and attract one another, and the ideal-gas answer can be badly wrong.

Pure Component Properties builds the description of a real pure fluid step by step: first how it fills space, then how its energy changes with temperature, then how far its properties depart from an ideal gas at the same state, and finally its fugacity, the quantity that decides when liquid and vapour can coexist. Mixtures, phase equilibrium of mixtures and reactions are left to the modules that follow.

Before you start

Be comfortable with the first law as an energy balance, the idea of entropy, partial derivatives, and the ideal-gas law PV = RT on a molar basis. No earlier ChETL module is required.

How the nine topics connect

Most topics build on quantities defined in earlier ones. The map shows those scientific relationships; the platform’s topic order, listed after it, is a teaching sequence that follows them closely but is not itself a chain of definitions.

Pure component and its statesubstance, temperature, pressure
Volumetric foundation
Compressibility factor ZMolar volume V
Residual (departure) properties MRreal fluid minus ideal gas at the same T, P
Thermal foundation Heat capacity CPideal-gas part of H and S
Ideal-gas part + residual, each on a stated reference
Enthalpy HEntropy S
Gibbs energy GG = H − TS
Fugacity f, φfrom residual Gibbs energy
Saturation propertiescoexistence criterion: equal fugacity of liquid and vapour
Solution Thermodynamics and Phase Equilibriumuse these pure-component quantities
Conceptual map, read from top to bottom. Residual properties come from the same volumetric description as Z and V; heat capacity is not needed for them. Both branches meet at enthalpy and entropy, each the sum of an ideal-gas part (from heat capacity) and a residual part. Enthalpy and entropy are siblings, neither defined from the other, and both feed G = H − TS; fugacity is built from the residual Gibbs energy. The arrow into saturation marks the thermodynamic criterion that defines coexistence, not the platform’s current calculation route (see below). Arrows do not claim that every calculation runs every earlier topic. Dashed boxes are context outside this module.

Platform topic order: a learning progression, not a chain of definitions

  1. Compressibility
  2. Volume
  3. Heat capacity
  4. Residual
  5. Enthalpy
  6. Entropy
  7. Gibbs energy
  8. Fugacity
  9. Saturation

Heat capacity sits before residual properties, and enthalpy before entropy, in the teaching order only; scientifically, residuals need no heat capacity, and enthalpy and entropy each stand on their own ideal-gas and residual parts.

The residual property is a departure from the ideal-gas state at the same temperature and pressure, evaluated from the same volumetric description (equation of state or generalised correlation) that gives Z and V. Heat capacity supplies the other ingredient, the ideal-gas change with temperature. Enthalpy and entropy are each assembled from an ideal-gas contribution plus the corresponding residual. Gibbs energy combines them, G = H − TS. Fugacity follows because the fugacity coefficient is defined through the residual Gibbs energy, GR = RT ln φ.

Saturation comes last because a pure fluid’s liquid and vapour coexist when their fugacities (equivalently, their molar Gibbs energies) are equal; the Theory develops that criterion. The platform does not currently solve it with an equation of state. Vapour pressure and boiling temperature come from named correlations (Antoine, Lee–Kesler or Clausius–Clapeyron) or, for water, IAPWS-IF97. The volume of vaporisation uses the cubic equation’s liquid and vapour roots at that saturation state, and the enthalpy and entropy of vaporisation use the Watson/Riedel correlation (or IAPWS-IF97 for water).

The nine topics and the questions they answer

1. Compressibility factor (Z)
How far is this fluid from ideal-gas behaviour?
Z = PV/RT is one at the ideal-gas limit. Its departure from one measures non-ideality, and comparing models shows how much that answer depends on the description chosen.
2. Molar volume (V)
How much space does the fluid occupy at this state?
Vapour or liquid molar volume from the same model families as Z, plus a dedicated correlation for saturated liquid.
3. Heat capacity (CP)
How strongly does energy change with temperature?
Ideal-gas heat capacity from polynomial correlations, and liquid heat capacity from a corresponding-states correlation. It provides the thermal baseline for enthalpy and entropy.
4. Residual properties (MR)
How large is the real-fluid departure from the ideal gas?
VR, HR, SR and GR, each the difference between the real fluid and an ideal gas at the same temperature and pressure.
5. Enthalpy (H)
How much energy does the state carry, on a stated reference?
A reference value, the ideal-gas change from the reference temperature, and the residual enthalpy, added together. Central to every energy balance.
6. Entropy (S)
How do temperature and pressure change entropy, and what does real-fluid behaviour add?
Thermal and pressure contributions plus the residual entropy, on a stated reference.
7. Gibbs energy (G)
Which potential governs equilibrium at fixed temperature and pressure?
G = H − TS, the bridge from energy and entropy to phase and reaction equilibrium.
8. Fugacity and fugacity coefficient (f, φ)
What is the real fluid’s escaping tendency?
φ = exp(GR/RT) and f = φP; at the ideal-gas limit φ = 1 and f = P.
9. Saturation properties
At what condition do liquid and vapour of this substance coexist?
Vapour pressure, boiling temperature, and the enthalpy, entropy and volume of vaporisation, tied together by the Clapeyron equation. Coexistence is defined by equal fugacity; the current routes are vapour-pressure correlations or IAPWS-IF97 rather than an equation-of-state equal-fugacity solve.

Ideal and real fluids: the reference idea

Most of the module turns on one comparison. For any property M (volume, enthalpy, entropy or Gibbs energy) the real fluid is compared with a hypothetical ideal gas at the same temperature and pressure:

MR = M − Mig  (same T, P)

The ideal-gas part is easy to calculate from heat capacities. All the difficulty of real behaviour is collected in the residual, which an equation of state or a generalised correlation supplies. This split is why the module can treat a gas near ambient conditions and a compressed liquid with the same machinery, and why the ideal-gas answer is always available as a check: Z → 1, MR → 0 and φ → 1 as pressure falls towards zero.

Choosing a model

Models are treated as different ways of computing the same defined property, so a topic can be studied with several and the answers compared. The families available in this module are:

  • Ideal gas: the low-pressure reference.
  • Truncated virial equation: a correction for vapours at low to moderate density; it does not describe liquids.
  • Cubic equations of state (Redlich–Kwong, Soave–Redlich–Kwong and Peng–Robinson): one equation for both vapour and liquid, solved for Z with the physically appropriate root selected.
  • Lee–Kesler generalised correlations: corresponding-states tables built from the critical temperature, critical pressure and acentric factor.
  • Correlations for specific properties: polynomial ideal-gas heat capacities, a corresponding-states liquid heat capacity, the Rackett equation for saturated-liquid volume, Antoine, Lee–Kesler and Clausius–Clapeyron forms for vapour pressure, and Watson/Riedel for the enthalpy of vaporisation.
  • IAPWS-IF97 for water: the industrial water and steam formulation, offered for water in molar volume, enthalpy, entropy and saturation.

Phase selection

Below the critical temperature a cubic equation can have both a vapour-like and a liquid-like root at the same temperature and pressure. Away from saturation, one of them is the stable phase; the other, where it exists, describes a metastable or hypothetical state, such as a superheated liquid below its vapour pressure. At the saturation pressure both are stable: they are the two coexisting phases. The default Auto mode decides the physical phase first and then checks whether the chosen model can represent it. Asking explicitly for Liquid or Vapour returns that branch with its status (stable, saturated, or metastable), or reports that it does not exist. At exactly the saturation pressure, Auto reports coexistence rather than silently picking one phase for properties such as volume and enthalpy that differ between them.

Validity

Every correlation carries a range. Coefficients, their units and their source are shown on the Blackboard before they are used, and the Interpretation tab flags results that rely on extrapolation. A model that cannot represent the configured state returns an unavailable result rather than a quietly substituted one.

Reference states and basis

Absolute enthalpy and entropy are only meaningful on a stated reference. ChETL reports enthalpy on a formation-referenced convention (the standard enthalpy of formation at 298.15 K, plus the ideal-gas change from 298.15 K, plus the residual) and entropy on a Third-Law basis. IAPWS-IF97 keeps the steam-table reference instead, with internal energy and entropy set to zero for saturated liquid water at the triple point.

Differences such as ΔH between two states on the same reference are physically meaningful. Absolute values on different references are not comparable, so a ChETL enthalpy should not be set beside a steam-table value or another program’s output without reconciling the zero first.

Results are reported on a molar basis. Where the molar mass is known and a mass-specific value has a standard engineering meaning, the mass basis is shown as the same result in different units, not as a second calculation.

Common misunderstandings

  • “Z tells me how to size the compressor.” Z corrects the volume at one state. Compressor work, power and vessel design need energy balances, efficiencies and design codes.
  • “Enthalpy is heat.” Enthalpy is a state property. It equals the heat transferred only under particular conditions, such as a closed system at constant pressure with no other work.
  • “Any root of the cubic is a valid answer.” A cubic can have three real roots; the middle one has no physical meaning. Away from saturation only one of the outer two is the stable phase, and the other is at best metastable; at the saturation pressure both are stable, coexisting phases.
  • “Fugacity is just a corrected pressure, so it is always close to P.” For a compressed liquid the fugacity can be far below the system pressure. It is close to the fugacity at saturation multiplied by a compression (Poynting) correction, which is small for modest compression but can become significant at pressures far above saturation.
  • “A correlation that worked at one temperature works everywhere.” Outside its fitted range a correlation is an extrapolation, and its error is unknown.

Scope and limits

  • One component at a time. Mixture properties are in Solution Thermodynamics; vapour–liquid equilibrium of mixtures is in Phase Equilibrium.
  • Heat capacity uses ideal-gas and liquid correlations; a real-gas heat-capacity route is not offered.
  • Component coverage depends on data: a component appears for a model only when the data that model needs are available.
  • Model results are estimates. Agreement between two models is not experimental validation, and results are for learning, not for design.

See it in the platform

The How it works tour follows the compressibility-factor topic for n-butane with the Peng–Robinson equation at 400 K and 10 bar, through Theory, Blackboard, Plot, Interpretation, AI Tutor, Assessment and Data. It demonstrates the workspace; it is not a full worked lesson.

Sources and next steps

  • J. M. Smith, H. C. Van Ness, M. M. Abbott and M. T. Swihart, Introduction to Chemical Engineering Thermodynamics, 9th ed.: the pure-fluid sequence of volumetric properties, heat effects, residual properties, fugacity and saturation that this module follows.
  • International Association for the Properties of Water and Steam, Revised Release on the IAPWS Industrial Formulation 1997 for the Thermodynamic Properties of Water and Steam (IAPWS-IF97), used for water.
  • This guide summarises ChETL’s documented module scope as of 9 November 2026; editorial responsibility rests with the ChETL Scientific Editor. See sources, review and limits; report errors through Contact.

Launch ChETL

Launch ChETL