Module guide · Available

Chemical Equilibrium: where a reacting mixture comes to rest

Given a reaction and a feed at a stated temperature and pressure, how far can the reaction go before it stops, and what would shift that limit? This module answers with the equilibrium constant, the extent of reaction and the composition they fix, first for one reaction and then for several that share species.

Part of Chemical Engineering Thermodynamics.

The question this module answers

Ammonia synthesis, methanol production and steam reforming are all limited by equilibrium: however good the catalyst and however long the reactor, the composition cannot pass the point where the forward and reverse tendencies balance. Knowing where that point lies, and how temperature, pressure and feed move it, is the first thermodynamic question in reactor and process design.

Thermodynamics fixes the destination, not the speed. This module therefore says nothing about rates, catalysts or residence time; those belong to reaction engineering.

Before you start

Gibbs energy, enthalpy and heat capacity from Pure Component Properties, reaction stoichiometry, and ideal-gas mixtures and partial pressures. The idea of activity from Solution Thermodynamics helps but is not essential for the current gas-phase scope.

One foundation, two composition problems

Thermochemical dataformation properties, heat capacities
Equilibrium constantwritten reaction and temperature → K(T)
Single-reaction equilibriumone equilibrium condition Multiple-reaction equilibriuman independent set solved together
Outcomescomposition, extent, conversion, yield, selectivity
Both composition topics use the same equilibrium-constant calculation; neither feeds the other. Extent, conversion, yield and selectivity are results derived from the equilibrium composition, not separate topics.

Suggested study order: a learning progression, not a scientific dependency

  1. Equilibrium constant
  2. Single-reaction equilibrium
  3. Multiple-reaction equilibrium

Find K for one written reaction, use it to close the composition of one reaction, then extend the same condition to several independent reactions solved together.

Reaction thermodynamics and K(T)

How does temperature change a reaction’s equilibrium constant?

For a reaction written with stoichiometric numbers νi (positive for products, negative for reactants), the standard Gibbs energy of reaction fixes the equilibrium constant:

ΔrG°(T) = Σ νi Gi°(T)   K(T) = exp[−ΔrG°/RT]

Because standard states are defined at a fixed pressure (1 bar for gases), K depends on temperature only. It also depends on how the reaction is written: doubling every stoichiometric number squares K. ChETL keeps the reaction exactly as entered rather than rescaling it.

Three temperature routes are taught: evaluation at the 298.15 K reference from formation data; the van ’t Hoff equation with a constant standard enthalpy of reaction; and a route that integrates the heat-capacity change of reaction, ΔrCP°. Heat-capacity correlations carry reported ranges; outside them the result is still calculated but marked as an extrapolation.

Notation: ChETL writes ΔrG°, ΔrH° and ΔrS° with a reaction subscript, and ξ for the extent of reaction. Smith, Van Ness and Abbott write ΔG° and ε; the quantities are the same.

One reaction: extent, composition and conversion

What equilibrium composition results from one reaction and a specified feed?

Every species amount follows from a single unknown, the extent of reaction ξ:

ni = ni0 + νi ξ   Q = Π aiνi   equilibrium: Q = K

For an ideal-gas mixture the activity is ai = yiP/P°. The feasible values of ξ are bounded by the species that run out first in each direction, and the solution lies inside that interval. Comparing the initial quotient Q0 with K tells which way the reaction will move, through ΔrG = RT ln(Q/K). Conversion is then calculated from the equilibrium extent; it is a derived measure, not a separate result.

What shifts the equilibrium

  • Temperature changes K itself. For an exothermic reaction K falls as temperature rises; for an endothermic one it rises.
  • Pressure leaves K unchanged but changes the composition when the total moles of gas change, Δν = Σνi ≠ 0. For an ideal-gas reaction with fewer moles of products (Δν < 0), higher pressure favours the products.
  • Inerts at fixed total pressure dilute the reacting species, with an effect like lowering the pressure when Δν ≠ 0.
  • Feed ratio and initial products change where the equilibrium lies and which reactant limits it, without changing K.

Temperature and pressure sweeps show the first two effects over a range in the Plot and Data tabs; feed and inert effects are explored by changing the feed and calculating again. Sweep limits are guards against meaningless ranges; they do not certify the property data across the whole range.

Several reactions: independent sets

How do several reactions compete for the same species?

With r reactions, each has its own extent and its own equilibrium condition, Qj = Kj(T), and all are solved together:

ni = ni0 + Σj νij ξj

Only independent reactions add information. A reaction that is a combination of others adds no new constraint, so the platform determines the rank of the stoichiometric matrix and works with an independent set from the reactions you enter. Different independent sets describing the same chemistry give the same equilibrium composition, even though their individual extents differ. Product distribution, yield and selectivity follow from that composition.

Reading the results

  • log K against T, with ln K against 1/T as an alternative view: the second is a straight line only when the standard enthalpy of reaction is constant, so its curvature shows how much the heat-capacity correction matters.
  • Equilibrium composition against temperature or pressure: the mole fraction of every species across one sweep, with the configured state marked.

Common misunderstandings

  • “Raising the pressure changes K.” K depends on temperature only; pressure moves the composition through Δν.
  • “A large K means a fast reaction.” Equilibrium says how far, not how fast.
  • “A catalyst shifts the equilibrium.” It speeds the approach without moving the destination.
  • “K is a property of the chemistry, whatever the coefficients.” Its value depends on how the reaction is written; compare values only for the same written form.
  • “Equilibrium conversion is what the reactor achieves.” It is the limit at those conditions. A real reactor reaches less, depending on rate and residence time.

Scope and limits

  • Homogeneous gas-phase reactions treated as ideal-gas mixtures. Real-gas fugacity corrections, liquid-phase and condensed species, and electrolyte or acid–base equilibria are not part of the current scope.
  • Reactions must be stated. Product prediction by Gibbs-energy minimisation without a reaction set is not offered.
  • Not included: simultaneous reaction and phase equilibrium, adiabatic reaction equilibrium with an energy balance, electrochemical equilibrium, kinetics and reactor sizing.
  • Data coverage. A species is offered only when the formation, heat-capacity and other data its route needs are available; gas-phase data are never used for another phase.

Sources and next steps

  • J. M. Smith, H. C. Van Ness, M. M. Abbott and M. T. Swihart, Introduction to Chemical Engineering Thermodynamics, 9th ed., chapter 14 (chemical-reaction equilibria).
  • Further treatments consulted for the module: J. R. Elliott and C. T. Lira, Introductory Chemical Engineering Thermodynamics; K. D. Dahm and D. P. Visco, Fundamentals of Chemical Engineering Thermodynamics; T. Matsoukas, Fundamentals of Chemical Engineering Thermodynamics; S. I. Sandler, Chemical, Biochemical, and Engineering Thermodynamics (reaction-equilibrium chapters).
  • This guide summarises ChETL’s documented module scope as of 9 November 2026; editorial responsibility rests with the ChETL Scientific Editor. See sources, review and limits; report errors through Contact.

Launch ChETL

Launch ChETL